watch dog for telephones

Watch-Dog for Telephones
Most of the telephone security devices available in market are simple but quite expensive. These devices provide blinking or beeping type line-tap/misuse indications. Quite often they do not offer guaranteed protection against unauthor-ised operation. A very simple and uni- que circuit of a telephone watch-dog to safeguard subscriber telephone lines against any fraud is described here. This little circuit keeps continuous watch over the telephone lines and sounds an alarm in case of any misuse. In addition it transmits a loud tone through the telephone lines to prevent further misuse. When switch S1 is turned on, the normal (on-hook) telephone line voltage at the output of bridge-rectifier diodes D1 to D4 is approximately 48 volts, which being well above the break-down voltage of zener diode D5, the diode conducts. As a result transistor T2 gets forward biased. This effectively grounds the base of transistor T1 which is thus cut off and the remaining circuit does not get any power supply. In this state, only a small (negligible) current is taken by the circuit, which will not affect the telephone line condition. However, when handset of any telephone connected to the telephone lines is lifted (off-hook), line voltage suddenly drops to about 10 volts. As a result, transistor T2 is switched off and transistor T1 gets forward biased via resistor R1. Now, the astablemultivibrator built around timer IC1 starts oscillating and the speaker starts sounding. Output of the astable multivibrator is also connected to the base of transistor T1 through capacitor C5. As a result, only a loud (and irritating) tone is heard in the ear-piece of the unauthorised telephone instrument. This circuit can be constructed on a veroboard using easily available low-cost components and it can be connected to any telephone line without the fear of malfunctioning. No extra power supply is required as it draws power from the telephone line for operation. Note: Please disconnect the gadget when you are yourself using the telephone as it cannot distinguish between authorised and unautho- rised operation

Read more...

anemometer

Read more...

circuit to generate surround sounds

Read more...

SESMIC SENSOR

Here is a simple sensor which can detect the seismic vibrations caused by a person or large animal walking nearby. A representative application for the sensor is a deer repellent for the vegetable garden. When a deer steps near the sensor a loud buzzer or beeper sounds for a few seconds startling the would-be vegetable thief away. The sensor also makes an effective intruder detector to catch trespassers as soon as they step on the property!
Deer Repellent/ Seismic Sensor :

The unit is designed to consume minute amounts of power to provide many months of unattended protection (practically set by the battery shelf life). The seismic sensor is built from an ordinary 2 inch speaker by gluing a mass to the speaker cone to lower its resonance frequency. A lid from a baby food jar with a little extra weight glued to the inside will work fine.
The CA3094 I.C. is an unusual op-amp consisting of a programmable transconductance amplifier connected to a darlington transistor. In this circuit the darlington is combined with a pnp transistor to form a monostable timer which determines how long the buzzer sounds. When the ground shakes, the vibration sensing speaker generates a small voltage which is amplified causing the voltage on pin 1 to go high. The darlington in the IC and the 2N4403 turn on with regenerative feedback provided by the diode. The 2N4401 turns on, powering the buzzer until the monostable resets. The circuit may be used to activate a variety of devices including a relay to control line voltage devices, a transmitter to telemeter an alarm from a remote location, a battery- powered walkway light, or even one of those battery powered squirt guns! The output transistor may be replaced with a power darlington transistor for directly controlling higher current loads. The circuit may be built into ordinary plumbing PVC pipe or practically any weatherproof enclosure. A larger detection area may be accomplished by burying a long pole or PVC pipe just below the surface of the ground with the seismic sensor located above the pole. Vibrations will readily travel down the pole whenever a footstep occurs anywhere along its length. The seismic sensor may be replaced with other sensors for different applications. A photocell/ resistor divider will sense changes in light level, a microphone will sense fairly low sound levels, and a diode detector will sense a low-level RF field.

Read more...

VIDEO ACTIVATED RELAY

This simple circuit from the May 1996 Think Tank column of Popular Electronics activates a relay when it senses a composite video signal. This allows you to use the tuner built into your VCR to turn on and off older TVs that are not equipped with a remote. It can also be used to activate surround sound equipment, turn off the room lights, turn on video game consoles, etc. For such a simple circuit, it is very versatile.

Parts
Part
Total Qty.
Description
Substitutions
R1, R2
2
10K 1/4 W Resistor
R3
1
1K 1/4 W Resistor
R4
1
33K 1/4 W Resistor
C1
1
1uF Electrolytic Capacitor
Q1, Q2, Q3
3
2N2222 NPN Transistor
2N3904 NPN Transistor
D1, D2, D3
4
1N4148 Diode
K1
1
9V Relay
J1
1
RCA Jack
MISC
1
Case, wire, board

Notes
Since you may be using this circuit to switch mains voltage, it should be enclosed in a case.
The circuit will also work with most line level audio, although you may have to adjust the value of R1.

Read more...

SIMPLE WATER LEVEL INDICATOR

Description This is the circuit diagram of a simple corrosion free water level indicator for home and industries.In fact the the level of any conductive non corrosive liquids can be measured using this circuit.The circuit is based on 5 transistor switches.Each transistor is switched on to drive the corresponding LED , when its base is supplied with current through the water through the electrode probes.
One electrode probe is (F) with 6V AC is placed at the bottom of tank.Next probes are placed step by step above the bottom probe. When water is rising the the base of each transistor gets electrical connection to 6V AC through water and the corresponding probe.Which in turn makes the transistors conduct to glow LED and indicate the level of water.The ends of probes are connected to corresponding points in the circuit as shown in circuit diagram.Insulated Aluminum wires with end insulation removed will do for the probe.Arrange the probes in order on a PVC pipe according to the depth and immerse it in the tank.AC voltage is use to prevent electrolysis at the probes.So this setup will last really long.I guarantee at least a 2 years of maintenance free operation.That’s what I got and is still going.

Components
T1 – T5 BC 548 or 2N2222 Transistors
R1-R5 2.2K 1/4 W Resistors
R6-R10 22K 1/4 W Resistors
D1 – D5 LED’s ( color your choice)
Notes
Use a transformer with 6V 500 mA output for power supply.Do not use a rectifier! we need pure AC. Use good quality insulated Aluminum wire for probes.If Aluminum wires are not available try Steel or Tin.Copper is the worst.Try the circuit first on a bread board and if not working properly, make adjustments with the resistance values .This is often needed because conductivity of water changes slightly from place to place.
Circuit Diagram and Sensor Arrangement

Read more...

SIMPLE LIE DETECTOR

Simple Lie Detector
Here's a simple lie detector that can be built in a few minutes, but can be incredibly useful when you want to know if someone is really telling you the truth. It is not as sophisticated as the ones the professionals use, but it works. It works by measuring skin resistance, which goes down when you lie.


CIRCUIT DIAGRAM :

Details of Parts
Here are the details of the specific parts you will needPart Total Qty. Description Substitutions
R1 33K 1/4W Resistor R2 5K Pot R3 1.5K 1/4W Resistor C1 1uF 16V Electrolytic Capacitor Q1 2N3565 NPN Transistor M1 0-1 mA Analog Meter MISC 1 Case, Wire, Electrodes (See Nots)Notes1. The electrodes can be alligator clips (although they can be painful), electrode pads (like the type they use in the hospital), or just wires and tape. 2. To use the circuit, attach the electrodes to the back of the subjects hand, about 1 inch apart. Then, adjust the meter for a reading of 0. Ask the questions. You know the subject is lying when the meter changes.

Read more...

HI-FI DX BASS CIRCUIT

Description.

Here is the circuit diagram of a passive DX bass circuit that can be used with almost all audio amplifiers.

comments on the circuit : The circuit that I have designed is a passive one but you can make it an active one by adding a pre amp at the output. The first stage acts as a main tone stage. It balances the bass and the treble. The 0.01 cap is for high frequency while the 0.22uF cap is for low frequency. The second stage is for sound compression. the caps works the same as at the first stage only that they are there to start the sound compression that is received from the input stage. The 2.2k resistor delays the sound thereby multiplying the compression. The 10k variable resistor is there used to tune the compression depending on the frequency of the speaker. If you are using 4 to 6 inches hi-fi speakers, I advise you to keep the 10k variable resistor at 0 ohm. The circuit is not copyrighted and you can change it to suit your requirement. All I ask is to be posting the updates of the circuit design on the site.

Circuit diagram.

Circuit diagram.

Notes.

• Assemble the circuit on a good quality PCB.
• This circuit does not require a power supply.
• POT R6 is for volume control.
• Switch S1 can be a slide switch and it is the DX Bass switch.

Read more...

FM PHONE TRANSMITTER

This project provides the schematic and the parts list needed to construct a FM Phone Transmitter. This device attaches in series to one of your phone lines. When there is a signal on the line (that is, when you pick up the handset) the circuit will transmit the conversation a short distance. In particular it will radiate from the phone line itself. It is a passive device - there is no battery. It uses the signal on the phone line for power. No aerial is needed - it feeds back the RF signal into the phone line which radiates it in the FM band. The frequency of transmission may be adjusted by the trimcap. Note that some countries may ban any electronic device which attaches to the telephone. It is the responsibility of the constructor to check the legal requirements for the operation of this FM Phone Transmitter and to obey them.

FM Phone Transmitter Schematic

FM Phone Transmitter Circuit Description

The circuit is a radio frequency (RF) oscillator that operates around 93 MHz (93 million cycles per second). Power for the circuit is derived from the full wave diode bridge. C1, C8, L3 & T1 forms the FM oscillator.

Every Tx needs an oscillator to generate the Radio Frequency (RF) carrier waves. L1, C6, T2 forms the power amplifier. Audio from the telephone

lines is coupled through R3 & C2 into the base of T1 to modulate the oscillator. This is done by varying the junction capacitance of the transistor. Junction capacitance is a function of the potential difference applied to the base of the transistor. R1 & C4 act as a low pass filter.

C3 is a high frequency shunt. L2 is call a RFC (radio frequency shunt.) It decouples the power and audio from the transmitter amplifier circuit. This type of circuit usually should be calibrated. The resonant frequency of the L1-C6 amplifier circuit should be adjusted to match the resonent oscillator frequency of C1, C9-L3. However, in practice, we think you will find that the unit operates perfectly OK as it is constructed without the need to calibrate anything. If you want to try calibration you will need a frequency meter, a CRO or just trial and error.

Calibrate by moving the coils of L1 further apart. With C1 at 27p you will find that the it tunes into the FM band in the 86 - 95 MHz area. With C1 at 22p the band is raised to about 90-95mhz (depending in the coil spacing.) If you want to move this tunable area still higher to over 100MHz range then replace C1 by a 15pF or 10pF capacitor. This assumes that the on-hook voltage is about the standard 48V. If the on-hook voltage of an extension phone network is lower, say about 39V, C1 will have to be lower in the 15p to 10p range to be in the commercial FM band in this case.

Note that you should not hold the printed circuit board physically in your hands if you try to do any calibration. Your own body capicitance when you touch it is more than enough to change the oscillation frequency of the whole unit.

You can experiment the FM Phone Transmitter to get greater transmission range away from the phone line by adding an aerial (about 150 cm of 26 gauge wire) to the collector of T2.

FM Phone Transmitter Assembly Instructions

The ZTX320 has a flat and a curved side. Match these two sides with the flat and curved sides as shown on the overlay for T2. Also note these points when assembling this project:

1) Two of the three coils have enamel insulation lacquer on them. This must be physically removed from both ends of the coil before it can be soldered. Now during the manufacture of these coils they have been solder dipped to remove this lacquer. But check each leg to see that this is the case.

2) Spread out the turns in the L3 coil about 1 mm apart. The coils should not touch.

3) A solder connection (or tap) is required from the top of the first turn in the L3 coil to the pad next to the coil. Solder a piece of wire to the top of the first turn as shown on the overlay. Then solder the other end to the pad immediately next to the L3 coil.

4) The cathodes of all diodes point to the top of the PCB.

5) Attach 3" of wire with an alligator clip on the end to the pads between the diodes marked - 'TO LINE' No aerial is needed. The phone line itself acts as a sufficient aerial. To make the Kit small, resistors & diodes stand on their ends. The kit attaches to ONE of the two phone lines going to your phone. Either of the two lines will do. In most of the world this is the green or red wire. In the UK it is one of the wires attached to the terminals 2 or 5. Cut the phone line. Attach one alligator clip to one cut end and the other alligator clip to the other cut end. Take your phone off the hook and turn on an FM radio at about 93 MHz. It should be very easy to tune into the transmission. Take a portable FM receiver outside and follow the phone line.

FM Phone Transmitter Parts List

Read more...

3V FM TRANSMITTER

This project provides the schematic and the parts list needed to construct a 3V FM Transmitter

. This FM transmitter is about the simplest and most basic transmitter to build and have a useful transmitting range. It is surprisingly powerful despite its small component count and 3V operating voltage. It will easily penetrate over three floors of an apartment building and go over 300 meters in the open air.

It may be tuned anywhere in the FM band. Or it may be tuned outside the commercial M band for greater privacy. (Of course this means you must modify your FM radio to be able to receive the transmission or have a broad-band FM receiver.) The output power of this FM transmitter is below the legal limits of many countries (eg, USA and Australia). However, some countries may ban ALL wireless transmissions without a licence. It is the responsibility of the constructor to check the legal requirements for the operation of this kit and to obey them.

The circuit is basically a radio frequency (RF) oscillator that operates around 100 MHz. Audio picked up and amplified by the electret microphone

is fed into the audio amplifier stage built around the first transistor. Output from the collector is fed into the base of the second transistor where it modulates the resonant frequency of the tank circuit (the 5 turn coil and the trimcap) by varying the junction capacitance of the transistor. Junction capacitance is a function of the potential difference applied to the base of the transistor. The tank circuit is connected in a Colpitts oscillator circuit.

The electret microphone: an electret is a permanently charged dielectric. It is made by heating a ceramic material, placing it in a magnetic field then allowing it to cool while still in the magnetic field. It is the electrostatic equivalent of a permanent magnet. In the electret microphone a slice of this material is used as part of the dielectric of a capacitor in which the diaphram of the microphone formsone plate. Sound pressure moves one of its plates. The movement of the plate changes the capacitance. The electret capacitor is connected to an FET amplifier. These microphones are small, have excellent sensitivity, a wide frequency response and a very low cost.

First amplification stage: this is a standard self-biasing common emitter amplifier. The 22nF capacitor isolates the microphone from the base voltage of the transistor and only allows alternating current (AC) signals to pass.

The tank (LC) circuit: every FM transmitter needs an oscillator to generate the radio Frequency (RF) carrier waves. The tank (LC) circuit, the BC547 and the feedback 5pF capacitor are the oscillator in the Cadre. An input signal is not needed to sustain the oscillation. The feedback signal makes the base-emitter current of the transistor vary at the resonant frequency. This causes the emitter-collector current to vary at the same frequency. This signal fed to the aerial and radiated as radio waves. The 27pF coupling capacitor on the aerial is to minimise the effect of the aerial capacitance on the LC circuit. The name 'tank' circuit comes from the ability of the LC circuit to store energy for oscillations. In a pure LC circuit (one with no resistance) energy cannot be lost. (In an AC network only the resistive elements will dissipate electrical energy. The purely reactive elements, the C and the L simply store energy to be returned to the system later.) Note that the tank circuit does not oscillate just by having a DC potential put across it. Positive feedback must be provided. (Look up Hartley and Colpitts oscillators in a reference book for more details.)

ASSEMBLY INSTRUCTION

Components may be added to the PCB in any order. Note that the electret microphone should be inserted with the pin connected to the metal case connected to the negative rail (that is, to the ground or zero voltage side of the circuit). The coil should be about 3mm in diameter and 5 turns. The wire is tinned copper wire, 0.61 mm in diameter. After the coil in soldered into place spread the coils apart about 0.5 to 1mm so that they are not touching. (The spacing in not critical since tuning of the Tx will be done by the trim capacitor. It is quite possible, but not as convenient, to use a fixed value capacitor in place of the trimcapacitor - say 47pF - and to vary the Tx frequency by simply adjusting the spacing of the coils. That is by varying L of the LC circuit rather than C.) Adding and removing the batteries acts as a switch.Connect a half or quarter wavelength antenna (length of wire) to the aerial point. At an FM frequency of 100 MHz these lengths are 150 cm and 75 cm respectively.

CIRCUIT CALIBRATION

Place the transmitter about 10 feet from a FM radio. Set the radio to somewhere about 89 - 90 MHz. Walk back to the FM transmitter and turn it on. Spread the winding of the coil apart by approximately 1mm from each other. No coil winding should be touching another winding. Use a small screw driver to tune the trim cap. Remove the screwdriver from the trim screw after every adjustment so the LC circuit is not affected by stray capicitance. Or use a plastic screwdriver. If you have difficulty finding the transmitting frequency then have a second person tune up and down the FM dial after every adjustment. One full turn of the trim cap will cover its full range of capacitance from 6pF to 45pF. The normal FM band tunes in over about one tenth of the full range of the tuning cap.

So it is best to adjust it in steps of 5 to 10 degrees at each turn. So tuning takes a little patience but is not difficult. The reason that there must be at least 10 ft. separation between the radio and the FM transmitter is that the FM transmitter emits harmonics; it does not only emit on one frequency but on several different frequencies close to each other. You should have little difficulty in finding the Tx frequency when you follow this procedure.

LEARNING EXPERIENCE

It should already be clear from the above circuit description that there is a surprising amount of electronics which may be learnt from this deceptively simple kit. Here is a list of some advanced topics in electronics which can be demonstrated or have their beginnings in this project:

Class C amplifiers; FM transmission; VHF antennas; positive and negative feedback; stray capacitance; crystal-locked oscillators; signal attenuation The simple halfwave antenna used in the project is not the most efficient. Greater efficiency may be gained by connecting a dipole antenna using 50 ohm coaxial cable. Connect one lead to the Antenna point and the other to the earth line.

You may experiment using 6V or 9V with the circuit to see how this increases the range of the transmitter. The sensitivity may be increased by lowering the 22K resistor to 10K. Try it and see. Note that this FM transmitter is not suitable for use on your body, for example, in your pocket. This is because it is affected by external capacitance and the transmitting frequency drifts depending how close you are to it. Stray capacitance is automatically incorporated into the capacitance of the tank circuit which will shift the transmitting frequency.

FM TRANSMITTER PARTS LIST

Read more...

HVAC THEMOSTAT

Introduction To HVAC Thermostat

HVAC thermostat has been one of the common device used in residential and industrial buildings to control the temperature of a space be it a warehouse, a room, a hall or an office. This thermostat project will focus on the heating control of a space that uses electric heater as its source of heating. It basically consists of a comparator that controls the ON and OFF of the electric heater

based on the sensor temperature.

The control of the fan speed is usually hardwired with two speed or three speed motors and is incorporated into the thermostat. The temperature range of this thermostat is from 5 Celcius to 30 Celcius with a tolerance of approximately 3 degree Celcius. Hence, only non critical tolerance control of temperature control such as a room can be used.

Circuit Description

The circuit diagram

shows the configuration of the HVAC thermostat. The LM358 Op Amp is used as a comparator to sense the inputs of the reference voltage (PIN 3) and room temperature (PIN 2). The thermistor used is a NTC (negative temperature coefficient) type where its resistance will drop when the temperature increases and vice versa. It has a resistance of 20K ohm at 25 degree Celcius. When the room temperature drops, the thermistor resistance will go up and hence the output of the operational amplifier

will be low. This cause the relay to turn OFF and the heater will conduct until the temperature of the room rises again.






The circuit is calibrated using variable resistor VR1. Set the lever of the slide potentiometer or rotary potentiometer VR2 to 25 Celcius location. Place the thermistor at a space where the temperature is at 25 Celcius. By varying VR1, set the resistance at the position between the ON and OFF of the relay. Use a suitable contact relay rating according to the load of the heater.

Parts List

Read more...

DATA ACQUISITION SYSTEM

Assembly
Please read all these instructions through once
before starting assembly. First note that 4
components are mounted underneath the double
sided, plated through PCB. The overlay shows these
components but they are mounted
UNDERNEATH the board on the copper side of
the PCB. The 4 components are C7 C8 R5 & R2.
C7, the 10uF tantalum capacitor must be pushed
over on its side so that the total height from the
surface of the PCB is under 5mm (otherwise it will
not fit inside the case.) The ceramic capacitor, C8,
also needs to be pushed over a little. The 1/8W
resistors will be under 5mm above the board.
All the other components are on the top of the PCB
as normal. Again the tantalum capacitor must be
pushed over to be under 5mm high. Make sure to
identify C6, the 103 monoblok capacitor and get it
in the right position. Make sure also that the two 10
pin IC’s are soldered in the right positions. U2 is the
MAX186. Note the orientation of the 1N4148
diode. The 78L05 must be mounted flush on the
PCB so it is not above 5mm. The resistor networks
can be either way around.
Make sure that the two DB25 connectors are
correct: J1 is male, J2 is female. Use one half of the case as a jig to hold the connectors & the PCB
before you solder any lugs. If you do not do this
then you run the risk that a connector will be skew
on the PCB & not fit properly into the case at both
ends.
The extra male DB25 connector & case are
provided for the power supply & inputs as
described in the documentation.
COMPONENTS KIT
0.1 104 monoblok .........C1 C2 C3 C5 .......... 4
0.01uF 103 monoblok ...C6 ........................... 1
1/8W 5% resistor
1K brown black red .....R5 ........................... 1
10K brown black orange R2 ......................... 1
10R brown black black .R1 ........................... 1
1N4148 diode ...............D1 ........................... 1
4.7uF/16V tantalum .......C4 ........................... 1
10uF/16V tantalum ........C7 ........................... 1
4K7 resistor network .....R3 R4 ...................... 2
74HCT373 ...................U1 ........................... 1
78L05 ...........................Q1 ........................... 1
220pF capacitor ............C8 ........................... 1
MAX186 ......................U2 ........................... 1
K118 PCB ..................................................... 1
D shell snap set ............................................... 1set
Male 25 pin PCB connector ......................... 2
Female 25 pin PCB connector ........................ 1
DB25 shell case .............................................. 1

FOR SOFTWARE VISIT www.electronickits.com/kit/complete/data/ck2000.htm

Read more...

5 BAND GRAPHIC EQUALIZER

This circuit uses a single chip, IC BA3812L for realizing a 5 band graphic equalizer for use in hi-fi audio systems.The BA3812L is a five-point graphic equalizer that has all the required functions integrated onto one IC. The IC is comprised of the five tone control circuits and input and output buffer amplifiers. The BA3812L features low distortion, low noise, and wide dynamic range, and is an ideal choice for Hi-Fi stereo applica-tions. It also has a wide operating voltage range (3.5V to 16V), which means that it can be adapted for use with most types of stereo equipment.

The five center frequencies are independently set using external capacitors, and as the output stage buffer amplifier and tone control section are independent circuits, fine control over a part of the frequency bandwidth is possible, By using two BA3812Ls, it is possible to construct a 10-point graphic equalizer. The amount of boost and cut can be set by external components.

The recommended power supply is 8V, but the circuit should work for a supply of 9V also. The maximum voltage limit is 16V.

The circuit given in the diagram operates around the five frequency bands:

100Hz
300Hz
1kHz
3kHz
10kHz

Read more...

DIGITAL VOLUME CONTROLLER

This circuit could be used for replacing your manual volume control in a stereo amplifier. In this circuit, push-to-on switch S1 controls the forward (volume increase) operation of both channels while a similar switch S2 controls reverse (volume decrease) operation of both channels.

A readily available IC from Dallas semiconductor, DS1669 is used here.

FEATURES:

Replaces mechanical variable resistors
Electronic interface provided for digital as well as manual control
Wide differential input voltage range between 4.5 and 8 volts
Wiper position is maintained in the absence of power
Low-cost alternative to mechanical controls
Applications include volume, tone, contrast,brightness, and dimmer control

The circuit is extremely simple and compact requiring very few external components.

The power supply can vary from 4.5V to 8V.

Read more...

2 TRANSISTOR FM VOICE TRANSMITTER

Warning:

Take care with transmitter circuits. It is illegal in most countries to operate radio transmitters without a license. Although only low power this circuit may be tuned to operate over the range 87-108MHz with a range of 20 or 30 metres.

Notes:

I have used a pair of BC548 transistors in this circuit. Although not strictly RF transistors, they still give good results. I have used an ECM Mic insert from Maplin Electronics, order code FS43W. It is a two terminal ECM, but ordinary dynamic mic inserts can also be used, simply omit the front 10k resistor. The coil L1 was again from Maplin, part no. UF68Y and consists of 7 turns on a quarter inch plastic former with a tuning slug. The tuning slug is adjusted to tune the transmitter. Actual range on my prototype tuned from 70MHz to around 120MHz. The aerial is a few inches of wire. Lengths of wire greater than 2 feet may damp oscillations and not allow the circuit to work. Although RF circuits are best constructed on a PCB, you can get away with veroboard, keep all leads short, and break tracks at appropriate points.


One final point, don't hold the circuit in your hand and try to speak. Body capacitance is equivalent to a 200pF capacitor shunted to earth, damping all oscillations

Read more...